How to Get Rid of Unwanted Odors from Car Exhaust article If you’re stuck in traffic on the freeway, the smell of a broken taillight is all that remains of your car’s old, dusty odors.
The best way to get those old smells out of your vehicle is to remove them.
A lot of us are accustomed to the smell from our cars, but when we start to notice them more and more often, it’s a good idea to take a step back and really analyze the situation.
It’s also important to recognize the source of the odors before they get out of hand.
There are a number of ways to get your old car’s odors out of the way.
Step 1: Get Rid Of the Car’s Old Exhaust Source Reddit /u/thejoe_loves_his_exhaust article There’s nothing quite like taking a few paces along a highway and seeing the smog that hangs over your vehicle.
You can take that moment to clean up the mess that’s left behind by the vehicle’s old exhaust system.
This isn’t just about removing any odors that might be lingering in the air.
You want to take care of any other potential contaminants as well, too.
Some of the best things to do are to remove the old exhaust from your car, then spray a thin layer of car exhaust oil over the area.
If you’re not comfortable using a vacuum cleaner, a blowtorch will do the trick.
Don’t let this method take too long.
Once the oil is sprayed over the car’s area, it will take up to an hour to dry.
While this method might not look appealing, the benefits are worth it.
You’ll be cleaning up any residual odors with a professional.
Step 2: Remove the Old Exterior Body Panels Source Reddit The Joes Favorite article If your car is already running well enough to run off of, it should be fairly easy to remove its old interior panels.
But how do you get those panels out of an old car without destroying its entire exterior?
Step 3: Remove Your Exhaust from Your Car’s Exterior and Body Panes Source Reddit Step 4: Remove The Coolant From Your Exterior Source Reddit You’ll want to remove all the coolant from the old vehicle’s exhaust system, too, so that you can start replacing the oil that’s sitting in it.
When you do this, the exhaust system should look something like this.
In order to do this properly, you’ll need to remove at least two panels from each of the two exhaust manifolds.
For the left exhaust, you need to lift the entire rear intake manifold and push it out.
Once you’re done, you can pull out the whole left intake manifold, too—just like that.
Then, pull the front and rear intake manifolds out.
You can see the coolants and coolant-rich air ducts that make up the two manifolds in the right-hand photo.
Now, the left-hand side is where the cooling and fluid flow is.
The right-side is where coolant and air flow is to be located.
Again, this is just a rough idea of the whole process.
There’s plenty of room to get this all out of here.
All that’s remaining is to reattach the two rear intake pipes and replace them with the front.
Step 5: Remove Any Suspension Connections Source Reddit Car Parts Experts article After you’ve pulled the exhaust out of its old location, it makes sense to start cleaning up the system again.
Start by removing the rear shock, which is a large piece of plastic that is attached to the rear suspension.
Grab a pair of pliers and pull the entire shock assembly out of it.
The back end of the shock assembly will be attached to two different pieces of plastic, one in the center of the assembly and one behind it.
Step 6: Remove Rear Suspension for the Front of Your Car and Replace it with the Rear Suspensions Article The JOs Favorite article If the front of your Subaru’s suspension system is a bit stiffer than your rear, it might not be possible to fully remove the front suspension.
So, if you’re using a Subaru Impreza or Legacy, you might want to swap out the front suspensions for a rear suspension instead.
First, open up the Subaru ImPreza’s firewall.
Remove the bottom of the firewall.
This should come out of a small opening near the firewall itself.
Next, take a pair or three of wire ties and tie it into a small, tight knot on the underside of the front end of your Imprezas front bumper.
With that done, carefully slide the wire ties behind the bumper and over the firewall, so the wire ends will be on the bottom, not the top.Step 7: